Submitted by Domepiece9 t3_126phuf in DIY
[removed]
Comments
MrRonObvious t1_jea47k1 wrote
On most motion detectors, you can flip the switch on and off rapidly to override the motion detector function. You'll have to check the owners manual.
mararch t1_jea62b2 wrote
Then when you shut it off for, I think, 5 seconds or more, it resets to motion detector mode.
Domepiece9 OP t1_jea6zv9 wrote
This is great. thanks.
Pinstrip3 t1_jea7gtf wrote
Yes, rather easy. Rewire the sensor so it's connected through a wall switch.
Domepiece9 OP t1_jea7xge wrote
currently have a regular porch light that is connected through a wall switch. I plan to replace that regular porch light with a motion detection porch light and run through the same switch. However, I was assuming wall switch would only turn motion detection on or off, but wanted to figure out a way to be able to turn on that light by overriding the motion detection with the same switch.
Pinstrip3 t1_jea8udq wrote
I believe You'd need a second set of cables or use third (ground) cable as a last resort.
If you connect the sensor to the switch you will be able to turn on/off the light but it will auto turn off after set period of time and go into motion sensing mode. That's how it works in my case anyway. Downside is I have to turn the switch off and back on to turn on the light.
Domepiece9 OP t1_jeabqg8 wrote
Check out a couple of the other responses in this thread. It sounds like you can override that in some models.
Pinstrip3 t1_jead6g8 wrote
Yeah, I've seen. I've got led lamps with built in daylight and motion sensors, rather cheap. I don't need them to stay on for longer periods so I just left it as is.
ark_mod t1_jeajmqn wrote
It looks like OP got the real answer in other responses. To explain in more detail for others...
What pinstripe suggests isn't easy at all for 99% of people and is the wrong way to do it. Yes you could disassemble your motion sensor, rewire the sensor, modify the external housing and run extra wires to the switch. But why? Depending on your skill level it could look professional or it could look like someone hacked you the electrical box... Not to mention the labor involved and the fact that this custom solution will be very confusing to anyone that does work in the future.
The correct way to do this is purchase a motion sensor with a built in always on feature. As others mentioned you just need to flick the power off/on to get it to stay on. Leave it off for longer you reset it. The switch then has standard wiring instead of a custom solution. If in the future you (or the next owner) wants to replacev the light they can without dealing with a custom switch and wiring related to modifying the sensor box.
My point - the are "off the shelve" solutions to this issue. No need to custom modify the light and sensor to achieve this.
chopsuwe t1_jeb7lcq wrote
Your submission has been removed for one or more of the following reason(s):
- Your question does not include the research you've done to find an answer yourself, or why that research didn't answer your question.
This is a basic requirement so others do not spend time repeating your steps. It is not a judgement about your question being "too easy." We're looking for evidence that you've made an attempt yourself.
-
Please do not use /r/DIY as your first stop for questions - we are not Google.
-
Please search Google and /r/DIY to see if your question has been asked before. Check owners manuals, tech support forums or contact the manufacturer.
-
Have you already done some basic research and are still stuck?
-
Please include what research you have done in your question so that others do not repeat your steps.
-
Consider posting your question in the sticky thread at the top of the subreddit.
-
Ask your question in our Discord server in the appropriate channel.
Please read our Full Sub Rules before resubmitting.
If you believe this was a mistake, please message the moderators.
###Do not respond to this comment - you will not receive a response.
Pinstrip3 t1_jebd27q wrote
What you suggesting is sounds to be the right solution.
On a side note I didn't mean to rewire the sensor itself but to simply connect it after the wall switch. That way it can be overriden by the switch, but only to turn it off, not to make it stay on.
Sometimes English is a struggle ;)
guy_n_cognito_tu t1_jea40fw wrote
Many motion detector lights have a feature where you can flick the switch off, then on very quickly, and that will deactivate the motion detection feature and give you constant on.